Flex TPO Для дома Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Para a casa Flex TPO Для дома. Flex TPO Для дома User Manual Manual do Utilizador

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir

Resumo do Conteúdo

Página 1 - INSTALLATION HANDBOOK

TPO MEMBRANEINSTALLATION HANDBOOKRoong SystemsTool and Supply ChecklistStep-by-Step InstructionsPhoto IllustrationsDetail DrawingsProduct List

Página 2 - FlexRoofingSystems.com

MECHANICALLY ATTACHED MEMBRANE PLACEMENTAND SECUREMENTThe substrate must be clean and dry prior to installing the Flex RoofMembrane. The type of Flex

Página 3

11Mechanically fastened Flex TPO membraneFlex fasteners and screws help make installationeasier and faster.

Página 4 - FLEX TPO PLUS

FLASHINGGeneral Flashing ConditionsFlex Reinforced Flashing Membrane is to be installed for the flashingof parapet walls, roof equipment curbs, expansi

Página 5

13Hanging the wall flashingRolling wall flashing into place

Página 6

14Flashing on an open top curbFlashing existing mechanical unit

Página 7

15Hand welding a field-fabricated flashingHand welding a pre-formed outside corner flashing

Página 8

Pre-formed inside corner flashingWall flashing with Flex Lip-T bar, with approved caulking16

Página 9

Wall flashing with metal counter-flashingFlexClad™metal drip edge, properly secured17

Página 10

Flex Trim Strip welded to FlexClad™ metal and field membraneApplying water block to a drain flange under thefield membrane18

Página 11

Installing a Flex TPO Flashing target sheet over the field sheetdrain openingTightening the clamping ring on a drain flashing19

Página 12 - Applying flashing adhesive

ABOUT FLEX ROOFING SYSTEMSFlex manufactures Elvaloy®KEE-, PVC- and TPO-based materials for thecommercial roofing industry. Our product research, qualit

Página 13 - Hanging the wall flashing

Welding a Flex pre-formed pipe boot to the field membraneClamp and caulking is required at the top of the pipe boot20

Página 14 - Flashing on an open top curb

Field-fabricated method with Flex TPO Flashing MembraneFlex Split Pipe Boot, a pre-fabricated flashing21

Página 15

Post support flashing, available pre-formed from FlexFlexClad™metal pitch pan, fabricated by the contractor22

Página 16

Pitch pan topped off with Flex Pourable SealerPitch pans solve difficult flashing details23

Página 17 - FlexClad

Through-wall scupper made of FlexClad™ MetalExpansion joint cover, with Flex TPO Reinforced FlashingMembrane24

Página 18 - field membrane

25ACCESSORIESWalkway Pads Install walkway pads in those locations as designated in the specifications.Thoroughly clean and prepare the area of the roo

Página 19

26PaversEither a protection sheet of Flex TPO Flashing Membrane or Flex 180NGeotextile Separation Layer must be installed under all concrete paverbloc

Página 20

27HOT AIR WELDING GUIDELINESHot Air Welding EquipmentA. The Flex Automatic Welding Machine is an electrically powered,self propelled device that utili

Página 21

28C. The Flex Pressure Roller is a silicon hand roller used for rolling thehot air welded seams.Silicon hand rollerD. Seam probe is a hand held instru

Página 22

29E. When using a portable generator for providing electrical power to theautomatic or hand held welders, a 9500 watt minimum output generatoris recom

Página 23

EQUIPMENT AND ACCESSORIES LISTINGClean, asphalt-free extension cord sufficient to handle power requirementsOne (1) pair of scissors per manTape measure

Página 24 - Membrane

Welding PreparationThe surfaces to be welded must be clean and dry. Check the membraneoverlaps to determine whether they have been contaminated with fi

Página 25 - Flex Walkway Pad

Cut a test sample across the width of the seam at least 1” wide andlonger than the width of the seam.Pull the welded seam sample apart and examine the

Página 26

Hand Welder OperationThe hand welder is generally utilized for flashing details and field seamsless than 10’ in length. Consult the welding machine manu

Página 27

Using a hand held hot air welder to install wall flashing33

Página 28 - Seam probe

Seam ProbingAll welded seams must be probed with the Flex Seam Probe to determinethe quality and integrity of the weld. Allow the hot air welded seam

Página 29

35ROOF REPAIR GUIDETemporary or Emergency RepairIn the event that the Flex Roofing System becomes damaged the build-ing owner may be required to make t

Página 30

Permanent RepairFlex requires that this repair be performed by a Flex ApprovedApplicator. This repair is required to be completed in accordance withcu

Página 31

Procedure to Repair Voids in Hot Air Welded SeamsPrepare the surface by removing debris, contaminants and ballast fromthe area of the membrane or flash

Página 32

Flex RhinoBond™ System - An Optional Installation TechniqueAs an alternative to manual mechanically attached systems, the FlexRhinoBond™System allows

Página 33

For more information on the high-production Flex RhinoBond™System,please call 1-800-969-0108 or visit www.FlexRoofingSystems.comThe Flex RhinoBond Tool

Página 34

4FLEX TPO PLUSMECHANICALLY ATTACHED ROOF SYSTEMSPERIMETER SHEET REQUIREMENTS AND FASTENER GUIDEPerimeter SheetsFlex TPO mechanically attached roof sys

Página 35

40DETAIL INDEXDrawing Content Page Flex Ref #TPO Insulation Attachment 41 1.04Membrane Sheet Layout 42 2.01Lap Cross Section 43 2.03Plate &a

Página 36

DETAILS41

Página 45

5Notes: 1) Fastener assembly spacing for perimeter sheets is the same asrequired for the fastener spacing of the roof field area sheets.*Installation

Página 56

GUIDE TO FLEX FASTENER AND FLEX PLATE PLACEMENTSThis guide is based on current FM Approvals for the field sheetsecurement criteria.Steel Deck or Struct

Página 63

Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501 FLEX TPO MEMBRAN

Página 64

67Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501 FLEX TPO MEMBRA

Página 65

Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501 FLEX TPO MEMBRAN

Página 66

Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501 FLEX TPO MEMBRAN

Página 67

SUBSTRATE PREPARATIONDefects in the substrate surface must be reported and documentedto the Building Owner’s Representative for assessment. The roofing

Página 68

Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501 FLEX TPO SELF ADH

Página 69

71Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501FLEX TPO ACCESSORIESI

Página 70

Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501FLEX TPO ACCESSORIESIte

Página 71 - FLEX TPO ACCESSORIES

Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501FLEX OLYBOND PRODUCTSIt

Página 72

Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501FLEX TPO FASTENERS: STA

Página 73 - FLEX OLYBOND PRODUCTS

Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501FLEX TPO FASTENERS: HEA

Página 74

Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501FLEX TPO FASTENERS: CD-

Página 75 - FLEX TPO FASTENERS:

Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501GYPTEC 1” Head Without

Página 76 - (For Base Sheet Attachment)

Flex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400,Leesport, PA 19533Phone: 1-800-969-0108Fax: 610-916-9501FLEX TPO PIPE GUARDSIte

Página 77 - PURLIN FASTENERS

79For additional information: Call Flex Roofing Systems1-800-969-0108 or visit our websitewww.FlexRoofingSystems.comThere you can search “Technical Docu

Página 78 - FLEX TPO PIPE GUARDS

Existing Single Ply Roof Membranes: If the existing membrane isto be left in place it must be cut into sections no larger than 100 squarefeet per each

Página 79 - Roofing Systems

Roong SystemsFlex Membrane International, Inc. 2670 Leiscz’s Bridge Road, Suite 400Leesport, PA 19533 Phone: 1-800-969-0108 Fax: 610-916-9501Flex

Página 80 - Roong Systems

is installed so the top of wood is flush with the top surface of the roofinsulation or recover board. The wood blocking width is to exceed thewidth of

Comentários a estes Manuais

Sem comentários